chordcheek0

How to Replace the Replacement Key Battery For the Saab 9-3 Saab owners have a unique set of steps to add a second key. It requires dealer support using a handheld computer called Tech-2. A new key and transponder are required to be purchased and programmed to the car. Change your keys regularly to prevent one from wearing out more than the next. This will also help to keep your keys in top condition. Replacement Case The new key fobs are not like the older Saab keys. They have electronics that make them difficult to duplicate. saab car key replacement has made theft of cars significantly more difficult than it was a few years ago. It also makes it more costly to replace keys that were lost. Every owner of a 9-3 Saab should have at minimum two working keys. It is expensive to replace a lost key as it requires replacing the CIM module, as well as programming the locking cylinders. Dealers will typically charge $100-$200 to complete this. There are ways to reduce these high cost. Some parts suppliers will use the code of a spare key to cut a new metal blade at a fraction that of a dealer. The key must be the exact identical to the original one for it to work in your vehicle. You can also change the case yourself by following these steps. You'll require an open-faced screwdriver and a lot of patience. With the screwdriver slowly break the plastic and remove the emergency key from the case. After the case is open remove all electronics and put them back in your new case. Be sure to put the correct key and badge back into the case as well. Replacement Battery The replacement battery for the Saab 9-3 is an affordable component that can be replaced quickly and easily. This YouTube DIY video Cyclone Cyd shows how to replace the battery of the remote key fob in just four steps. This tutorial is suitable for any modern-day saab key fob however, the procedure may differ slightly. The button is typically located near the Saab logo on the back of the fob. The button is usually found on the back of your fob, right next to the Saab Logo. Use a flathead to insert the screwdriver through the small hole in this button. This will allow you to open the case of the fob to allow you to replace the battery. After the new battery CR1632 is in place then you can reassemble your remote key fob and program it to your car. The entire process should not take more than an hour at most. This is a straightforward process that doesn't require any special tools. If you lose a key, the procedure will be somewhat more complex however, it can be completed. The dealer will first need to read the VIN of the vehicle and order an additional TWICE module and key blade that has the correct unique code. The dealer will then need to program the key using MDI, a brand new software tool. Replacement Key Fob The key fob contains batteries that are used to lock and unlock your car. The batteries last for a certain time, and they will eventually die. This is a problem that occurs that affects all cars. The good thing is that you can replace the battery on most key fobs, and not have to replace the entire case. You can buy replacement fobs from Amazon that come with all the electronic components already installed, so you can just pop open the case and replace the old batteries. You'll need to take out the emergency key before you can replace the batteries. To do this, you need to insert a small flathead screwsdriver into the slot that is in the middle. Use the screwdriver to move around the case until it is split open, making it simple to remove. When you're ready to replace your keys, make sure you have spare keys, as this can reduce your total cost by a substantial amount. If you have an additional key, ask the dealer to cut it and program it to your vehicle. This is less expensive than buying a new key fob. If you don't have a spare, it is possible to add an additional key to your car, but this requires a lot research and effort. It will cost you a few hundred dollars to add a second car key. The computer of the vehicle also has to be programmed. This can be accomplished by a professional, but it's an expensive option for the majority of owners. Replacement Ignition The modern SAAB 9-3 is an alarm system that is more sophisticated based on a key code. If you lose your primary key, it may be costly to get another one because the car must be equipped with a specific computer and be programmed to accept a new key. Locksmiths typically aren't able to program this, and even dealers will charge hundred dollars to program the new key! If you've lost your only working key, a dealer will replace the computer in your car (known as the CIM or SAAB TWICE) to create a replacement, and will charge you the highest price for it. We can reprogram the existing EEPROM on your car's computer to make it ready for an extra key. This will save you more than 50% on what you would pay an auto dealer. If you have owned a 9-3 from SAAB for a long time and you're aware of the ignition keys aren't very durable. They can be extremely sticky, and the buttons can be removed from them every now and then and you should think about purchasing a new one if yours isn't functioning properly. It's not as difficult as it appears to replace the ignition key. With the right tools, it is able to be accomplished in a short time.